C Ercoli

Summary

Affiliation: University of Rochester
Country: USA

Publications

  1. ncbi request reprint Restoration of immediately loaded implants in a minimal number of appointments: a retrospective study of clinical effectiveness
    Carlo Ercoli
    Eastman Institute for Oral Health, School of Medicine and Dentistry, University of Rochester, Rochester, NY 14620, USA
    Int J Oral Maxillofac Implants 27:1527-33. 2012
  2. doi request reprint The influence of verification jig on framework fit for nonsegmented fixed implant-supported complete denture
    Carlo Ercoli
    Division of Prosthodontics, Eastman Institute for Oral Health, School of Medicine and Dentistry, University of Rochester, Rochester, NY 14620, USA
    Clin Implant Dent Relat Res 14:e188-95. 2012
  3. doi request reprint In vitro comparison of the cutting efficiency and temperature production of ten different rotary cutting instruments. Part II: electric handpiece and comparison with turbine
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, Department of Mechanical Engineering, University of Rochester, 625 Elmwood AveRochester, NY 14620, USA
    J Prosthet Dent 101:319-31. 2009
  4. doi request reprint In vitro comparison of the cutting efficiency and temperature production of 10 different rotary cutting instruments. Part I: Turbine
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, Rochester, NY 14620, USA
    J Prosthet Dent 101:248-61. 2009
  5. ncbi request reprint Restoration of immediately placed implants in 3 appointments: from surgical placement to definitive prostheses
    Carlo Ercoli
    University of Rochester, Eastman Dental Center, Rochester, NY 14620, USA
    J Prosthet Dent 96:212-8. 2006
  6. ncbi request reprint Face-bow record without a third point of reference: theoretical considerations and an alternative technique
    C Ercoli
    Eastman Dental Center, University of Rochester, Rochester, NY 14620, USA
    J Prosthet Dent 82:237-41. 1999
  7. ncbi request reprint The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: a study of drill durability
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, 625 Elmwood Avenue, Rochester, NY 14620, USA
    Int J Oral Maxillofac Implants 19:335-49. 2004
  8. ncbi request reprint Effect of soldering on metal-porcelain bond strength in repaired porcelain-fused-to-metal castings
    D F Galindo
    University of Rochester Eastman Dental Center, Rochester, NY, USA
    J Prosthet Dent 85:88-94. 2001
  9. ncbi request reprint Technique for fabricating a cement-retained single-unit implant-supported provisional restoration in the esthetic zone
    Mario R Ganddini
    Division of Prosthodontics, University of Rochester Eastman Dental Center, 625 Elmwood Avenue, Rochester, NY 14620, USA
    J Prosthet Dent 94:296-8. 2005
  10. doi request reprint Oral rehabilitation of a 12-year-old patient diagnosed with a central giant cell granuloma using a fibula graft and an implant-supported prosthesis: a clinical report
    Heeje Lee
    Department of Prosthodontics, Louisiana State University School of Dentistry, New Orleans, LA 70119, USA
    J Prosthet Dent 99:257-62. 2008

Collaborators

Detail Information

Publications24

  1. ncbi request reprint Restoration of immediately loaded implants in a minimal number of appointments: a retrospective study of clinical effectiveness
    Carlo Ercoli
    Eastman Institute for Oral Health, School of Medicine and Dentistry, University of Rochester, Rochester, NY 14620, USA
    Int J Oral Maxillofac Implants 27:1527-33. 2012
    ..The purpose of this study was to assess the clinical effectiveness of an experimental technique versus the conventional method for the fabrication of implant-supported fixed complete dentures...
  2. doi request reprint The influence of verification jig on framework fit for nonsegmented fixed implant-supported complete denture
    Carlo Ercoli
    Division of Prosthodontics, Eastman Institute for Oral Health, School of Medicine and Dentistry, University of Rochester, Rochester, NY 14620, USA
    Clin Implant Dent Relat Res 14:e188-95. 2012
    ..Materials and..
  3. doi request reprint In vitro comparison of the cutting efficiency and temperature production of ten different rotary cutting instruments. Part II: electric handpiece and comparison with turbine
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, Department of Mechanical Engineering, University of Rochester, 625 Elmwood AveRochester, NY 14620, USA
    J Prosthet Dent 101:319-31. 2009
    ....
  4. doi request reprint In vitro comparison of the cutting efficiency and temperature production of 10 different rotary cutting instruments. Part I: Turbine
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, Rochester, NY 14620, USA
    J Prosthet Dent 101:248-61. 2009
    ..Therefore, rotary cutting instruments for crown preparation are generally marketed with weak or unsupported claims of superior performance...
  5. ncbi request reprint Restoration of immediately placed implants in 3 appointments: from surgical placement to definitive prostheses
    Carlo Ercoli
    University of Rochester, Eastman Dental Center, Rochester, NY 14620, USA
    J Prosthet Dent 96:212-8. 2006
    ..This technique reduces chair time for both the patient and the clinician, and could ultimately reduce the cost of implant treatment and potentially increase treatment acceptance...
  6. ncbi request reprint Face-bow record without a third point of reference: theoretical considerations and an alternative technique
    C Ercoli
    Eastman Dental Center, University of Rochester, Rochester, NY 14620, USA
    J Prosthet Dent 82:237-41. 1999
    ..The elimination of a reference plane, to which relate the functional determinants of occlusion, avoids an additional source of error during the mounting procedure...
  7. ncbi request reprint The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: a study of drill durability
    Carlo Ercoli
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, 625 Elmwood Avenue, Rochester, NY 14620, USA
    Int J Oral Maxillofac Implants 19:335-49. 2004
    ..The authors evaluated, under conditions simulating implant placement, the cutting efficiency, durability, heat production, and wear of implant drills...
  8. ncbi request reprint Effect of soldering on metal-porcelain bond strength in repaired porcelain-fused-to-metal castings
    D F Galindo
    University of Rochester Eastman Dental Center, Rochester, NY, USA
    J Prosthet Dent 85:88-94. 2001
    ..Visual analysis revealed a significant difference in the amount of porcelain remaining on the fracture surface of the test and control samples; a complete quantitative elemental analysis with SEM/EDS is in progress...
  9. ncbi request reprint Technique for fabricating a cement-retained single-unit implant-supported provisional restoration in the esthetic zone
    Mario R Ganddini
    Division of Prosthodontics, University of Rochester Eastman Dental Center, 625 Elmwood Avenue, Rochester, NY 14620, USA
    J Prosthet Dent 94:296-8. 2005
    ..This article describes the fabrication of a provisional restoration for a single-unit implant-supported crown...
  10. doi request reprint Oral rehabilitation of a 12-year-old patient diagnosed with a central giant cell granuloma using a fibula graft and an implant-supported prosthesis: a clinical report
    Heeje Lee
    Department of Prosthodontics, Louisiana State University School of Dentistry, New Orleans, LA 70119, USA
    J Prosthet Dent 99:257-62. 2008
    ..The multidisciplinary approach successfully restored function and esthetics. Considerations regarding the extensive surgical and prosthetic rehabilitation of a young adult with remaining growth are discussed...
  11. ncbi request reprint Measurement of the rotational misfit and implant-abutment gap of all-ceramic abutments
    Wael N Garine
    Eastman Dental Center, Division of Prosthodontics, University of Rochester, Rochester, New York 14620, USA
    Int J Oral Maxillofac Implants 22:928-38. 2007
    ....
  12. ncbi request reprint Transition from failing dentition to a fixed implant-supported restoration: a staged approach
    Luca Cordaro
    Department of Periodontics and Implant Dentistry, Eastman Dental Hospital, Rome, Italy
    Int J Periodontics Restorative Dent 27:481-7. 2007
    ..The main drawbacks are extended treatment time, adjustments of the provisional restorations, and no less than two surgical steps...
  13. ncbi request reprint Oral rehabilitation of a completely edentulous epidermolysis bullosa patient with an implant-supported prosthesis: a clinical report
    Heeje Lee
    Division of Prosthodontics, University of Rochester Eastman Dental Center, and Department of Dentistry, Strong Memorial Hospital, Rochester, NY 14620 2989, USA
    J Prosthet Dent 97:65-9. 2007
    ..This treatment option appears to be favorable for EB patients, compared to other options involving removable prostheses, in that it causes less mechanical irritation to the oral mucosa...
  14. ncbi request reprint Influence of cold working and thermal treatment on the fit of implant-supported metal-ceramic fixed partial dentures
    Salman A Lakhani
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, Rochester, NY 14620, USA
    J Prosthet Dent 88:159-69. 2002
    ..The application of porcelain may alter the fit of metal-ceramic frameworks. In fixed partial denture frameworks, this altered fit may cause marginal opening and require sectioning and soldering of the prosthesis...
  15. ncbi request reprint Retrospective evaluation of complete-arch fixed partial dentures connecting teeth and implant abutments in patients with normal and reduced periodontal support
    Luca Cordaro
    Section of Periodontics and Implant Dentistry, Eastman Dental Hospital, University of Rochester Eastman Dental Center, Rochester, NY, USA
    J Prosthet Dent 94:313-20. 2005
    ..The clinical outcome of complete-arch fixed prostheses supported by implants and natural tooth abutments in patients with normal or reduced periodontal support has been reported by few studies, with controversial results...
  16. ncbi request reprint Verification jig for implant-supported prostheses: A comparison of standard impressions with verification jigs made of different materials
    Jorge E De La Cruz
    Division of Prosthodontics, University of Rochester, Eastman Dental Center, Rochester, NY 14620, USA
    J Prosthet Dent 88:329-36. 2002
    ..Implant verification jigs are routinely used during the fabrication of implant-supported prostheses. The dimensional accuracy of these jigs is unknown...
  17. ncbi request reprint A technique to produce a mirror-image wax pattern of an ear using rapid prototyping technology
    Majd Al Mardini
    University of Rochester Eastman Dental Center, Rochester, NY, USA
    J Prosthet Dent 94:195-8. 2005
    ..The 3-D computer model was inverted, using computer-aided design software. A physical thermoplastic (wax) pattern of the inverted 3-D cast was produced using a rapid prototyping (RP) machine...
  18. ncbi request reprint A comparison of the porcelain fracture resistance of screw-retained and cement-retained implant-supported metal-ceramic crowns
    Eduardo Torrado
    Division of Prosthodontics, University of Rochester Eastman Dental Center, NY 14620, USA
    J Prosthet Dent 91:532-7. 2004
    ..The presence of a screw opening on the occlusal surface of implant-supported metal-ceramic crowns may decrease the porcelain fracture resistance and shorten the longevity of the crown...
  19. ncbi request reprint An indirect technique for fabrication of a post and core wax pattern
    Theresa M Hofstede
    Department of Restorative Dentistry, College of Dental Medicine, Nova Southeastern University, Ft Lauderdale, FL, USA
    J Prosthet Dent 87:341-2. 2002
  20. ncbi request reprint Comparative evaluation of casting retention using the ITI solid abutment with six cements
    Ahmed Mansour
    Division of Prsothodontics, University of Rochester Eastman, Department of Dentistry, Rochester, NY 14620, USA
    Clin Oral Implants Res 13:343-8. 2002
    ..The purpose of this study was to test the retention of metal copings fabricated to fit on the one-groove, one flat-sided solid titanium abutment using six different cements...
  21. ncbi request reprint Comparison of the load at failure of soldered and nonsoldered porcelain-fused-to-metal crowns
    Min Sok Kang
    Division of Prosthodontics, Eastman Dental Center, University of Rochester, 625 Elmwood Avenue, Rochester, NY 14620, USA
    J Prosthet Dent 90:235-40. 2003
    ..The application of solder material to metal frameworks could affect the porcelain-to-metal failure load and possibly compromise the longevity of porcelain-fused-to-metal crowns...
  22. ncbi request reprint Prosthodontic application for implant carriers
    Mario R Ganddini
    Division of Prosthodontics, University of Rochester Eastman Dental Center, Rochester, NY, USA
    J Prosthet Dent 92:399-402. 2004
    ....
  23. doi request reprint Effect of subgingival depth of implant placement on the dimensional accuracy of the implant impression: an in vitro study
    Heeje Lee
    Department of Prosthodontics, Louisiana State University School of Dentistry, New Orleans, LA 70119, USA
    J Prosthet Dent 99:107-13. 2008
    ..PURPOSE.: The purpose of this study was to evaluate the effect of subgingival depth of implant placement on the accuracy of implant impressions...
  24. ncbi request reprint Tooth preparation: a study on the effect of different variables and a comparison between conventional and channeled diamond burs
    Daniel F Galindo
    Eastman Dental Center and College of Applied Sciences, Department of Mechanical Engineering, University of Rochester, Rochester, NY, USA
    J Prosthodont 13:3-16. 2004
    ..The purpose of this study was to evaluate the different variables involved in tooth cutting to characterize intrapulpal temperature generation, cutting efficiency, and bur durability when using conventional and channeled diamond burs...